Magtrol  
Motor Test Equipment
Dynamometer Controllers
DSP6001
 
 
PRODUCTS
SERVICES
SUPPORT
DATA SHEETS
COMPANY
CONTACT
SITE MAP
 
 

DSP6001 High Speed Programmable Controller

SpecificationsSystem OptionsData SheetManual
*Not recommended for new designs.*
Magtrol's Model DSP6001 High-Speed
Programmable Dynamometer Controller employs
state-of-the-art Digital Signal Processing Technology
to provide superior motor testing capabilities. Designed
for use with any Magtrol Hysteresis, Eddy-Current* or Powder Brake* Dynamometer, Magtrol In-Line Torque Transducer or auxiliary instrumentation, the DSP6001 can provide complete PC
control via IEEE-488 or RS-232 interface. With 120 readings
per second, the DSP6001 is ideally suited for both the test lab and the production line.
   
 
Features
Two Channels:: Enable the unit to support up to two testing instruments with independent or tandem configurations.
Built-in Alarm System: For power, speed, torque, temperature, air flow, water flow, electrical overload and external inputs
Torque/Speed Analog Outputs: For interface with a data acquisition system or strip chart recorder
Two Standard Computer Interfaces: RS-232 and IEEE-488
High Speed Data Acquisition: 120 torque and speed points per second via IEEE bus
(approx. 60/sec. via RS-232)
High Quality, Easy-to-Read Vacuum Fluorescent Readout: Displays torque, speed, power, auxiliary and PID (proportional gain, integral and derivative) values
Fast Full-Curve Data Acquisition: Free-run to locked rotor in seconds
Speed & Torque Operating Modes: Provide independent PID settings for improved Dynamometer control
Built-in Current Regulated Supply: For use with Hysteresis Dynamometer only
Adjustable Torque Units: English, Metric and SI are standard
Dynamometer Overload Protection ---
Digital Filter: Removes undesired noise from torque signals
Cross Loop Function: Allows closed loop control of brake via torque transducer
Programmable Digital PID Values: Controlled and stored via M-TEST software or controlled manually
Saving: Saves programmed values within configuration
Auxiliary ± 10 VDC Analog Input: For additional transducer
Single or Multi-point Torque and Speed Stabilized Testing: Via M-TEST software
Calibration: Closed box calibration
Rack Mounting: 19 in (482.6 mm) rack mounts with handles
 
Applications
In the laboratory, the DSP6001's high sample rate provides superior resolution for data acquisition and curve plotting. This allows for capturing more usable motor test data during switching, breakdown and other transitional areas of the motor test curve. For production and incoming inspection, the DSP6001 displays torque, speed and power at all times, allowing the dynamometer controller to be used as a manual stand alone unit or as part of a complete PC system.
 
Back to top
 
Technical Specifications
 
MEASUREMENT CHARACTERISTICS
Maximum Torque 10,000 units, ±5 V TSC1, ±10 V TSC2
Maximum Speed 99,999 rpm
Accuracy Speed:  0.01% of reading from 10 rpm to 100,000 rpm
TSC1:  0.02% of range (±1 mV)
TSC2:  0.02% of range (±2 mV)
ELECTRICAL CHARACTERISTICS
Fuses (5 × 20 mm)
Brake: UL/CSA 1.25 A 250 V SB
  IEC 1.00 A 250 V T
Power (120 V): UL/CSA 800 mA 250 V SB
Power (240 V): IEC 315 mA 250 V T
Power Requirements 75 VA
Voltage Requirements 120/240 V  60/50 Hz
Max. Compliance Voltage 45 VDC, Brake Output
INPUTS AND OUTPUTS
Input Voltage Range TSC1:  ±5 VDC
TSC2:  ±10 VDC
Accessory
Torque/Speed Output
Torque:  ±10 VDC
Speed:  ±10 VDC
Ctrl Out 0–3 VDC
ENVIRONMENT
Operating Temperature 5 °C to 40 °C
Relative Humidity < 80%
Temperature Coefficient 0.004% of range/°C of 5 VDC for both channels
 
Back to top
Magtrol, Inc (USA): 716-668-5555 • magtrol@magtrol.com ~ Magtrol SA (Switzerland): 41 (0)26 407 3000 • magtrol@magtrol.ch ~ Magtrol India: 91 (0)80 6561 395 7· girish@magtrol.in
Magtrol Contact Us English French German Chinese India Russian Motor Test Equipment Torque Transducers Load-Force-Weight Systems Brakes and Clutches Displacement Transducers Rotary Transmitters