Magtrol  
Motor Test Equipment
Accessories
Tables
 
PRODUCTS
SERVICES
SUPPORT
DATA SHEETS
COMPANY
CONTACT
SITE MAP
 
 

Dynamometer Tables

Table GalleryData Sheet
 
Test from a stationary position or move a dynamometer to alternate testing stations with ease with Magtrol's Dynamometer Table. The stand is designed from lightweight aluminum with casters for smooth mobility, and is sturdy enough to support even the heaviest of Magtrol dynamometers. The design can be retrofitted to any Magtrol dynamometer and is easily reconfigured for added versatility. Dynaometer Table
 
Features
  • Easy Mobility: Casters, which incorporate a high-grade nylon wheel with a die-cast aluminum frame, provide 360° rotation
  • Sturdy Construction: Made from extruded aluminum, the dynamometer table is lightweight, strong and corrosion-resistant
  • Leveling Jacks: When at rest and in operation, hand-operated leveling jacks, with rubber pads for vibration control, lift the casters from the floor to provide a solid foundation
  • Versatile: Its industry accepted T-slot extrusions accommodate standard fractional or metric fasteners allowing easy reconfiguration
  • Blower Mounting: To accommodate blowers required for brake cooling of certain HD/ED Dynamometers, tables are drilled and tapped for convenient blower mounting underneath the table top.
  • Built-in Shelf: For calibration beam, tools and accessories. Also used for mounting of TSC 401 Torque-Speed Conditioner and DES Power Supply (for tables ordered with WB/PB Series Dynamometers).
 
Custom Tables and Options
  • 19" Rack Mounts: Can be added for dynamometer controllers, readouts, power analyzers and other supporting electronics
  • Table Height: Choose from 2 different working heights to allow testing from either a standing or seated position
  • Top Shelf: Fits over any standard dynamometer table and dynamometer (see photo below)
  • Locking Drawer: Ideal for a laptop computer
  • Built-in Cabinet: For storage of tools and accessories
  • Multiple Dynamometers: Up to 3 sets of mounting holes can be drilled and tapped to accommodate up to 3 dynamometers, depending on the model
  • Fixtures and Protective Covers: Can be added to any basic table at an additional cost. Some assembly required.
Top Shelf - Can be added to any standard
dynamometer table (P/N 204430)
Custom table with rack mounts,
2-door cabinet and lockable tilt-out drawer
 
Back to top
 

 
Dynamometer Table Gallery

TABLES FOR HD / ED DYNAMOMETERS
For HD-100, 400, 500 and 700 Series Dynamometers with short base plate and ED-715 Dynamometers* For HD-100, 400, 500 and 700 Series Dynamometers with long base plate For HD-800 Series Dynamometers with long base plate and ED-815 Dynamometers* For HD-825 Dynamometers with long base plate
Grooved table top with five 10 mm T-slots: one centered, two 250 mm apart and two 350 mm apart. Mounting holes are pre-drilled and tapped.
Base of dynamometer also serves as the table top.
Grooved table top with three 12 mm T-slots: one centered and two 250 mm apart.
For tables ordered with HD-710 and HD-715 Dynamometers, blowers will be shipped mounted under the table top.**
Blower mounting hardware kit sold separately.
For tables ordered with HD-710 and HD-715 Dynamometers, blowers will be shipped mounted under the table top (as shown).**
Blower mounting hardware kit sold separately.
For tables ordered with HD-810 and ED/HD-815 Dynamometers, a blower mounting hardware kit will need to be purchased if under-the-table mounting (as shown) is desired. Assembly required. For tables ordered with HD-825 Dynamometers, a blower mounting hardware kit will need to be purchased if under-the-table mounting (as shown) is desired. Assembly required.
TAB 1457S TAB 1457L TAB 0800L TAB 0825L

  * Mounting of ED Engine Dynamometers to dynamometer tables requires certain modifications. Contact Magtrol for details.
** If table is NOT ordered at the same time as the dynamometer, a blower mounting hardware kit may be purchased.

TABLES FOR WB / PB DYNAMOMETERS
For WB/PB 43 Series Dynamometers For WB/PB 65 Series Dynamometers For WB/PB 115 Series Dynamometers For 1 & 2 WB/PB 15 Series Dynamometers
Grooved table top with five 10 mm T-slots: one centered, two 160 mm apart and two 350 mm apart. Grooved table top with three 12 mm T-slots: one centered and two 250 mm apart. Grooved table top with three 12 mm T-slots: one centered and two 250 mm apart. Grooved table top with three 14 mm T-slots: one centered and two 250 mm apart.
TAB 0043 TAB 0065/0115 TAB 0065/0115 TAB 0015

The TSC 401 Torque-Speed Conditioner and DES 31X Power Supply are shown mounted to a vibration-isolated plate which is bolted to the bottom shelf.

CUSTOM TABLE EXAMPLES
Lift table suitable for WB/PB 115 Tandem Dynamometers For 3 & 4 WB/PB 15 Series Dynamometers
• Dynamometer, TSC, DES and EK control mounting provisions
• 10 inch (254 mm) total travel accommodates various motor center heights
• 4-point locking for position stability
• Smooth vertical motor height adjustment
• DIN 650-14 H12 T-slots
• Welded steel construction
• 3" x 3" x 1/4" tubular frame
• Dynamometer, TSC, and DES mounting provisions
• DIN 650-14 H12 T-slots, one centered and two 250 mm apart
• Welded steel construction
• 3" x 3" x 1/4" tubular frame
TAB 0115 TL TAB 3415
 
Back to top
 
 
 
Magtrol, Inc (USA): 716-668-5555 • magtrol@magtrol.com ~ Magtrol SA (Switzerland): 41 (0)26 407 3000 • magtrol@magtrol.ch ~ Magtrol India: 91 (0)80 6561 395 7· girish@magtrol.in
Magtrol Contact Us English French German Chinese India Russian Motor Test Equipment Torque Transducers Load-Force-Weight Systems Brakes and Clutches Displacement Transducers Rotary Transmitters